It's a big mistake for me....
I see that yours is on an intersection prefab ...
I created one for testing, it works ...
but it does not work on a road ....
Why ?
How to make the "Trajectories" on the 1.36?
- Miritellane
- Posts: 242
- Joined: 09 Dec 2016 09:22
- Location: Vendée
- Contact:
Last edited by Miritellane on 10 May 2020 06:30, edited 2 times in total.
Maybe disable AI on that road and place 2 straight trajectories there.
Currently working on: various stuff
#1 forum spammer
Enjoying PM since 1.52
YouTube channel [PL]: http://youtube.pl/vooytek
- Miritellane
- Posts: 242
- Joined: 09 Dec 2016 09:22
- Location: Vendée
- Contact:
I tested, but it does not work, the Ai disappears by touching the node of the road ...
I think it will be necessary to arrange to place a prefab at each start or end of the area with trajectories ...
Anyway, thank you very much for this help.
I want to make my map evolve as well as possible ....
Ajouté 11 heures 19 minutes 26 secondes après :
Hello Today, I tested several configurations which prove that it is absolutely necessary to start on a prefab (but not all of them are compatible),
but I still have one point to find: how to tell the vehicle on the trajectory that it is not a priority when leaving the trajectory?
I tested several priority values but it didn't change anything,
I tested priority or stop signs, it doesn't work either ...
Do you have an idea or something?
Thank you
I think it will be necessary to arrange to place a prefab at each start or end of the area with trajectories ...
Anyway, thank you very much for this help.
I want to make my map evolve as well as possible ....
Ajouté 11 heures 19 minutes 26 secondes après :
Hello Today, I tested several configurations which prove that it is absolutely necessary to start on a prefab (but not all of them are compatible),
but I still have one point to find: how to tell the vehicle on the trajectory that it is not a priority when leaving the trajectory?
I tested several priority values but it didn't change anything,
I tested priority or stop signs, it doesn't work either ...
Do you have an idea or something?
Thank you
15 is the highest priority, 1 is the lowest.
If you want a zip merge, set both paths to the same value.
if you want the bus to give way, set it to a lower value than the main road.
If you want a zip merge, set both paths to the same value.
if you want the bus to give way, set it to a lower value than the main road.
Currently working on: various stuff
#1 forum spammer
Enjoying PM since 1.52
YouTube channel [PL]: http://youtube.pl/vooytek
- Miritellane
- Posts: 242
- Joined: 09 Dec 2016 09:22
- Location: Vendée
- Contact:
I did 2 tests with priority on the trajectories, as indicated,
once with just priority 1 on the bus trajectory,
once by adding a central trajectory on the road for the other vehicles, with a priority 15 ..
This does not change anything, the buses leave directly and collide with the other vehicles ...
See pictures... !
once with just priority 1 on the bus trajectory,
once by adding a central trajectory on the road for the other vehicles, with a priority 15 ..
This does not change anything, the buses leave directly and collide with the other vehicles ...
See pictures... !
It does not matter where to create the path - on the road or on the prefab. The main rule is to disable traffic on this section of the road or prefab.
First separate sections of the trajectory are created - directly, the exit, the stop, the entrance to the main road Then parameters are assigned for each section of the path. Then the sections are connected (the nodes are magnetized to each other)
In front of the connection of trajectories need to put additional nodes. The priority of this additional node extends to all nodes related to one section of the trajectory. The beginning and end of the trajectory should be as accurate as possible to the junction of roads.
Good luck
First separate sections of the trajectory are created - directly, the exit, the stop, the entrance to the main road Then parameters are assigned for each section of the path. Then the sections are connected (the nodes are magnetized to each other)
In front of the connection of trajectories need to put additional nodes. The priority of this additional node extends to all nodes related to one section of the trajectory. The beginning and end of the trajectory should be as accurate as possible to the junction of roads.
Good luck
- Miritellane
- Posts: 242
- Joined: 09 Dec 2016 09:22
- Location: Vendée
- Contact:
Hello
I followed your explanations to the letter,
the trajectories work on the roads ...
but the priorities are not recognized ....
Which causes accidents ...
I followed your explanations to the letter,
the trajectories work on the roads ...
but the priorities are not recognized ....
Which causes accidents ...
- Miritellane
- Posts: 242
- Joined: 09 Dec 2016 09:22
- Location: Vendée
- Contact:
Hello
And a big thank you, it works flawlessly ...
I will be able to take my bus stops (and others) and make them more realistic ...
I thank you all for your help.
Looking forward
And a big thank you, it works flawlessly ...
I will be able to take my bus stops (and others) and make them more realistic ...
I thank you all for your help.
Looking forward
-
- Information
-
Who is online
Users browsing this forum: No registered users and 0 guests